13777445666
13064745888

新闻中心 [ NEWS CENTER ]

当前位置: 网站首页 > 新闻中心 > 行业资讯
  • 电脑刺绣机断线的比较实用解决办法
  • 本站编辑:杭州萧山金铭绣花设备商行发布日期:2018-05-22 15:30 浏览次数:

在操作电脑刺绣机时,如果,某个机头特别爱断线,可以用以下步骤解决比较简单实用:

1、先用手摸旋梭,有无毛刺,要是有,应该把这个旋梭换了!

2、看针位深浅,旋梭位子有没有跑,,注意把机器转到196度,打开针板,将针按下去,看位置,必须针孔的下端离旋梭尖的下方必须有1.5到2毫米左右的距离,还有旋梭尖必须和针是一条直线,针后平面与旋梭尖保持一根头发丝的距离,如没有,必须达到这些要求。

 

3、看针板空有无毛刺,又必须用砂纸打磨

4、换针杆与针

5、以上办法试过都不可以,就把针按下去,用手抓住针夹,上下运动,要是间隙超过3毫米就更换,滑块,驱动器还有铝连杆,小连杆,往大连杆注入黄油,来减少间隙,在用手抓住跳线干A,转到250度左右上下晃,看凸轮间隙大小和,7.94滚珠是否脱落。

 

6、以上试过都不可以,最后一招,机器转到172度,把主轴固定死,不能让他动具体什么办法自己想,然后把车壳,所说的机头右方主轴上的偏心夹头松了,用手抓住偏心凸轮,就是4件套转动,要左右转动,找一个运动轨迹,在运动轨迹的比较低端,上紧夹头,感觉不好,和眼力不好的,可以用表,一般没有表的,一个头问题不大,头数多了就不可以了。

      相信通过以上几条方法过后,绣花机断线的问题应该可以得到比较快的解决。不要总是把时间浪费在等机修的功夫上!

2-1P305105J0-51.jpg

When operating a computer embroidery machine, if a particular head loves to break the line, the following steps can be used to solve the simplest and practical:

1, first touch the shuttle with your hand, there is no burr. If there is, you should change the shuttle.

2, see the needle position depth, the spindle seat is not running, pay attention to the machine to 196 degrees, open the needle plate, the needle press down, look at the position, the lower end of the needle hole must be 1.5 to 2 millimeter below the tip of the spindle, and the tip of the shuttle must be a straight line with the needle, and the pin plane and the spindle tip keep a hair thread. The distance, if not, must meet these requirements.

3, see whether there is burr in the needle plate, and must use sandpaper to polish it.

4. Needle exchange and needle

5, the above measures can not be tried, the needle press down, with the hand grip clip, up and down movement, if the gap is more than 3 millimeter change, slider, driver and aluminum rod, small connecting rod, into the Dalian rod into butter, to reduce the gap, with the hand to grab the jump line A, turn to 250 degrees or so to sway up and down to see cam clearance about 250 degrees. Size and size, whether 7.94 balls fall off.

6, the above test can not, the last trick, the machine to 172 degrees, the spindle is fixed to death, can not let him move the specific way of thinking, and then the car shell, the right side of the right side of the spindle on the eccentric clip on the spindle, with the hand to seize the eccentric cam, is the 4 sets of rotation, to turn around, looking for a movement track, in a movement track, in the track, in a movement track, in the track, in the track, in a movement track, in the track, in the track, in the track, find a movement locus, in the track, in the track, in the track, in a movement track, in the The lowest end of the track, the tight chuck, the feeling is not good, and the eye is not good, can use the table, generally have no table, a head problem is not big, the head number is not possible.

I believe that after the above methods, the problem of embroidery machine disconnection should get the fastest solution. Don't always waste time waiting for machine repair.